| | |  | Fuse Holders | Home » » » » » » » SINGLE ANL FUSE HOLDER | | | | | | | Description: | | Scosche EWFH Single ANL Fuse holder | | | Features: | |
• Platinum-Plated Wiring Terminals and Accessories
• Durable Finish and Conductivity
• 2- and 4-Position Distribution Blocks Along With A Wide Range Of Fuse Sizes
• Easy Installation Of Multiple Amplifier Combinations
| | | Product Details: | | | Product Length:
| 5.7 inches | | Product Width:
| 6.0 inches | | Product Height:
| 2.0 inches | | Product Weight:
| 0.1 pounds | | Package Length:
| 6.3 inches | | Package Width:
| 1.2 inches | | Package Height:
| 0.3 inches | | Package Weight:
| 1.8 pounds | | Average Customer Rating:
|  based on 23 reviews |
| | | | Customer Reviews: | |
Average Customer Review:
 ( 23 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
48 of 57 found the following review helpful:
 Everything is "right sized"Apr 15, 2010
By HMMWV
"God, Country, Corps"
... For a 1000 watt 12VDC system.
Fuses for 12VDC can not have much drop across the fuse because the battery (fully charged) is 12.8 VDC and the battery is considered "drained" at 10.5 VDC. That's only 2.3 V of drop in your entire system including wires, connectors, fuses, and the battery. It's better if you have an alternator and engine running but they'll give you 124A or so while the battery can deliver 1000 amps. At 1000 watts constant power you will pull 115 Amps - that leaves you with 0.02 ohms for your entire wiring system to run 1000W with a charged battery and 2.3 V drop. If your battery is running low, consider it more like 0.01 ohms of max system loss. If your engine is on up at 14VDC you get some slack so long as your alternator <-> battery link is good.
You still need a fuse in the system though because the alternatives working with these power levels are arcwelding.
These high current fuses are optimal for such systems. For 1000W consider a minimum of 150 amps or possibly a 200 amp fuse. The clear plastic covers protect the screwdown terminals from stray metal and let you get a visual on the fuse status should it blow (it won't be pretty if it does blow - stopping a 115A DC current is going to produce a nasty arc and will also leave smoke inside the cover - no problem telling if the fuse blew!
A little secret - if you wonder why it is so hard to stop high power (200+ amps) DC and easy with AC it's that with 60Hz AC the voltage is exactly zero 60 times per second and usually stops on its own, so your arc lasts for a maximum of 1/60th second and with a sine wave source it naturally tapers down to zero where it stops. DC will go on forever if the gap isn't large enough.
10 of 10 found the following review helpful:
Scosche EWFH Single ANL Fuse HolderMar 20, 2010
By OldFart
I like these better then the other inline fuse because they are well covered and easy to replace and tell if they are blown.
8 of 8 found the following review helpful:
Great DC FUSE for battery systemApr 08, 2011
By Me
I bought this to be a fuse between a set of batteries and my inverter that powers a subpanel at my house for back-up capabilities. The casing and ANL fuse holder worked as intended. I was using 2 guage welder cable with a large 1/2" ring adapter. The fuse holder had no problems closing down over the connector and wire. It is nice beign able to see the fuse indicator as well to see if I had a problem or surge. This device gives me a peace of mind when it comes to saving my very expensive xantex prosine 2.5 from overloading on the DC side.
The cost is low and the feeling of safety is great. The plastic didnt' seem overly cheap and the stainless nuts and washers seemed quality. Very happy with the purchase.
8 of 9 found the following review helpful:
holds the fuseApr 10, 2009
By James Weister
holds the fuse, plastic cover a little brittle, needs a good amount of force to snap cover on, it is not water tight, looks good
3 of 3 found the following review helpful:
Fuse HolderJun 15, 2011
By Bobby Case
Fuse holder came on time as expected. You should know that no fuse comes with the holder. I also ordered fuses at the same time as the fuse holder. Still have not received the fuses.
See all 23 customer reviews on Amazon.com
| | |
|
